• +91-7300712189
  • info@nikitapapers.com
  • Opening: 10:00am - 7:00pm

Call Now+91-7300712189

Send Messageinfo@nikitapapers.com

Our LocationC10, industrial estate, panipat Road, Shamli


India is a vast country with an average of 700 pulp and paper mills. It is one of the highest polluting industries in India and is highly water intensive. Relatively large wastewater discharges and accompanied release of high pollution load into the environment is the sequel of high water consumption and pollution generation in the process of pulp and paper manufacture. Steps are been taken to preserve the resources, especially water which is an integral part of the pulp and paper industrial functioning. The need of cleaner production programs has been felt in recent times by the paper industry by way of a resource and waste minimization concept. In India efforts have been going on for years to improve house keeping, optimize process parameters, increase recycles and adopt improved technology. This paper aims at highlighting the process used during manufacture, sources and types of waste generated and treatment options available for improving the quality of waste to be discharged.




Pulp and paper industry, Cleaner production, Primary and Secondary treatment.



Water is a precious commodity and nature’s greatest gift to the living kingdom. Total utilizable water resources in India in 2005 have been estimated to be 1122 billion cubic meter per year, 38% of which is presently exploited for total national use (Dahasahasra and Panse, 2005). Water consumption in agriculture, industrial sector and domestic purposes are 85.3, 8.0, and 6.6% respectively. Water use in industrial sector is 34 billion m3 per year which is estimated to increase by four folds by 2050. With the continuously increasing demand and strong competition among industrial, agricultural and domestic sectors, water availability will be severely affected particularly to the large consuming industrial sectors like pulp and paper. Present national norm of water consumption per tonne of paper is 200 and 250 m3 in agro and large pulp and paper sectors whereas that set up World Bank is much lower (56 and 55 m3 per tonne of pulp and paper). By reducing the water consumption to 75m3 per tonne of pulp and paper the paper industry can produce double the amount of paper with the existing water allocation/draw. Pulp and paper industry is the third largest water consuming industrial sector in the country (www. water and agro industries. org/pulp paper.htm). Fresh water consumption in wood based, agro-based and waste paper based mills is 125-200, 125-225, 75-100 m3 per tonne of paper respectively (Chakrabarti, 2006). With average water consumption was 151m3 per tonne of paper. With the moderate per capita paper consumption of 10kg, water demand in this sector might increase to more than 1.5billion cubic meter with the current rate of water consumption.

Manufacture of Paper

The basic steps in making paper include;

– Suspension of cellulosic fiber prepared by beating it in water so that the fibers are thoroughly sepa- rated and saturated in water.

– Paper stock filtered on a woolen screen to form matted sheets of fiber.

– The wet sheet pressed and compressed to squeeze out a large proportion of water.

– The remaining water removed by evaporation.

– Depending upon use requirement, the dry paper sheet is compressed, coated or impregnated.

– Hydropulping

Sources of Waste Generation

In pulp and paper industry, considerable quantity of water is used in paper making processes. The quantity of water consumption varies according to the quality and kind of paper to be manufactured. In addition considerable amount of solid waste and gaseous emission occurs.

(i) Waste Water Generation

– Washing wooden chips in large-scale pulp and paper mills using wool as raw material.

– Washing of bagasse for separation of pith.

– Washing of rice/ wheat before pulping.

2. Pulping and bleaching

– Washing of chemically cooked pulp.

– Washing of pulp during bleaching.

– Pulp cleaning equipments.

3. Stock preparation and paper machine

– Cleaning of pulp in cleaning equipment.

– Filtration for wire section of paper machine.

– Paper machine presses.

4. Chemical recovery

– Foul condensate from evaporator and steam surface condenser.

– Boiler blowdown.

Beside above major sources of wastewater generation there are frequent leakages of black liquor from pump glands and its improper handling, which contribute significant color and pollution to the stream.

(ii) Solid Waste Generation

In pulp and paper industry solid wastes are generated from following operation;

– Raw material handling.

– Rejects from screening and centri-cleaners.

– Primary and secondary sludges from wastewater treatment system.

– Coal or boiler ash from steam and power genera- tion.

– Lime sludges from causticizing section of chemi- cal recovery plant.

(iii) Air Pollution

In pulp and paper industry air pollution is caused due to odour emitting reduced sulphur compounds such as hydrogen sulphide, methylmercaptan, dimethly sulphide, and particulate matter SO2 and NOx present in the gases emitted by different process units. Gaseous emission from pulp and paper mills can be broadly classified into the following categories:

• Gases from digesters.

• Gases from multiple effect evaporators.

• Gases from recovery.

Characteristics of Pollutants

Pulp and paper industry is intensive in terms of raw material consumption. Besides pollution load generation, the other consumption includes chemical, energy, water and capital requirements. About 41.8% of wood is recovered as bleached pulp. Of the remaining wood, roughly 4.2% ends up as solid waste, 5.25% goes into wastewaters as dissolved organic matter and 2.3% goes as suspended solids in wastewater (Nemade et al. 2003). The potential pollutants from pulp and paper mill fall into four principal categories as under:

Water effluents

– Suspended solids including bark particles, fiber, pigments and dirt.

– Dissolved colloidal organics like hemicelluloses, sugars, lignin compounds, alcohols, turpentine, sizing agents, adhesives like starch and synthetics.

– Color bodies, primarily lignin compounds and dyes.

– Dissolved inorganics such as NaOH, Na2SO4 and bleach chemicals.

– Thermal loads.

– Microorganisms such as coliform group.

– Toxic chemicals.


– Malodorous sulphur gases such as mercaptans and H2S released from various stages in Kraft pulping and recovery process.

– Oxide of sulphur from power plants, kraft recovery furnace and lime kiln.

– Steam.


– Fly ash from coal fired power boilers.

– Chemical particles primarily sodium and calcium based.

– Char from bark burners.

Solid wastes

– Sludges from primary and secondary treatment and causticizing in kraft mill recovery section.

– Solids such as grit bark and other mill wastes.

– Ash from coal fired boilers.

Water Conservation Measures

Pulp mill

– Raw material washing should be done with treated effluent.

– Washing efficiency of pulp washers should be improved.

– Paper machine back water should be used in the pulp dilution in the unbleached tower.

– Backwater should be used in centri cleaning of pulp and vacuum pump sealing.

– Bleach plant filtration should be recycled in pulp dilution in tower and vat, and shower sprays in the preceding stage.

Paper machine

– Efficiency of fiber separation with gravity save-all, krofta or disc filter should be increased to the best possible extent.

– Clarified back water of the fiber separator equipment should be used in pulper and head box dilution.

– Clarified back water should also be used in all showers except in felt cleaning.

– Cooling tower for vacuum pump and winder brake drum water should be installed and the water should be recycled.

– The condensate recovery in paper machines should be increased and reused in DM water make up.

– Back water should be utilized for alum/ PAC, filler and other chemical preparation.

Boiler house

– Treated effluent should be used in ash quenching

– Membrane based process for water softening should be installing in place of conventional chemical process.

Pollutional Effects

The main polluting constituents in pulp and paper mill wastewater are suspended solids, color, foam, inorganics such as sodium carbonate, bicarbonate, chlorides and sulphates, toxic chemicals such as mercaptans and inorganic sulphides. The effluent has high BOD and COD and when discharged untreated will damage the receiving water courses due to the presence of high oxygen demanding organics and inorganic constituents. Further the effluents impart colour to the stream and it persists for a long distance since lignin and its derivatives present in the effluent are not readily biodegraded. The effluent may also impart odour to the stream.

Cleaner Production

Cleaner production means continuous application of an integrated approach to improve mill operation through adoption of modern technologies, optimized process operation, resource recovery and maximum output per unit of the raw material inputs. The Indian paper industry still uses old pulping technologies and elemental chlorine bleaching resulting in high level of AOX generation. Cleaner technologies for pulping of raw materials are continuous pulping, RDH pulping, oxygen delingnification and for pulp bleaching are elemental chlorine free bleaching (EFC), chlorine dioxide bleaching, oxygen /peroxide bleaching.

Elements of Cleaner Production

There are few approaches to achieve cleaner production, which are known as CP technologies.

Source Reduction: It includes the change in existing practices or introducing new techniques in operating and maintaining equipments. The prevention of spills and leakages are typical house keeping measures.

Process change: It includes four options viz: change in input material, better process control, equipment modifications, and change in technology.

Recycling : This covers on site recovery and reuse of materials and energy which otherwise was a waste. Recovered material is better used in same process or for other purposes.

Product Modification: Produce high yield varieties of paper in order to minimize the environmental impact from the disposal of the product.